絞り込み
for pit gray water
-
O-M (4P) mechanical seal models- On-Land Pumps (Cast Iron)Direct-Coupled/Self-Priming Models
for agricultural
for industrial equipment
for pit gray water
for well water
●The specially structured casing enables self-priming without filling the suction pipe.
●The shaft seal uses a mechanical seal that facilitates daily maintenance.
●All cast iron is the standard specification, so it can also be used for alkaline liquids.
● Use of sealed ball bearings eliminates the need to lubricate the bearings. -
O-G (4P) gland packing models
- On-Land Pumps (Cast Iron)Direct-Coupled/Self-Priming Models
- for agricultural
- for industrial equipment
- for pit gray water
- for well water
●The specially structured casing enables self-priming without filling the suction pipe.
●The shaft seal uses a gland packing method that is easy to replace.
●All cast iron is the standard specification, so it can also be used for alkaline liquids.
● Use of sealed ball bearings eliminates the need to lubricate the bearings. -
O (4P) gland packing models- On-Land Pumps (Cast Iron)Direct-Coupled/Self-Priming Models
- for agricultural
- for industrial equipment
- for pit gray water
●The specially structured casing enables self-priming without filling the suction pipe.
●The shaft seal uses a gland packing method for easy maintenance.
●All cast iron is the standard specification, so it can also be used for alkaline liquids.
● Use of sealed ball bearings eliminates the need to lubricate the bearings. (OL-8E to O-9E)
(O-10E and O-11E are open ball bearings with grease injection) -
OH (4P) gland packing models- On-Land Pumps (Cast Iron)Direct-Coupled/Self-Priming Models
- for agricultural
- for industrial equipment
- for pit gray water
- for well water
●The specially structured casing enables self-priming without filling the suction pipe.
●The shaft seal uses a gland packing method for easy maintenance.
●All cast iron is the standard specification, so it can also be used for alkaline liquids.
● Use of sealed ball bearings eliminates the need to lubricate the bearings. (OH-3E to OH-6E)
(OH-7E to OH-9E are open ball bearings with grease injection) -
OW/OHW (4P) mechanical seal models (tandem type)- On-Land Pumps (Cast Iron)Direct-Coupled/Self-Priming Models
- for industrial equipment
- for pit gray water
●Two mechanical seals are mounted on the shaft seal (tandem type).
The mechanical seal on the atmosphere side is an oil bath type, which greatly improves the shaft sealing performance.
●The specially structured casing enables self-priming without filling the suction pipe.
●All cast iron is the standard specification, so it can also be used for alkaline liquids.
● Use of sealed ball bearings eliminates the need to lubricate the bearings. -
TO (4P) gland packing models- On-Land Pumps (Cast Iron)Direct-Coupled/Self-Priming Models
- for agricultural
- for industrial equipment
- for pit gray water
● Impellers can be easily attached and detached with jack bolts.
●Maintenance can be performed without disconnecting the piping.
●All cast iron is the standard specification, so it can also be used for alkaline liquids.
●Improve the durability of the pump.
●Further pursuit of self-priming capability. -
CX models (non-automatic)/CXA models (automatic)- Submersible PumpsPlastic/stainless steel models
for fishing- for industrial equipment
for kitchen wastewater- for pit gray water
for septic tank
for the chemical industry
● Compact and lightweight type that is convenient to carry and install.
● All wetted parts are made of resin and stainless steel (SUS316), which greatly improves rust resistance and durability.
●Eliminates clogging with a uniquely developed vortex structure.
●Original development of high-efficiency, energy-saving impellers and electric motors.
●Equipped with an automatic burnout prevention device in the motor. -
PX models (non-automatic)/PXA models (automatic)- Submersible PumpsPlastic/stainless steel models
- Products for general households
- for industrial equipment
- for kitchen wastewater
- for pit gray water
- for septic tank
●Lightweight, compact and hard to clog.
● All wetted parts are made of resin and stainless steel for excellent rust resistance and durability.
● New mechanism that can change the discharge direction either "vertically" or "horizontally". (excluding 1.5kW and 2.2kW)
● Back pull-out structure that allows inspection and cleaning while piping is connected.
●Equipped with an automatic burnout prevention device in the motor.
● Cooling and lubricity of the mechanical seal are improved by adopting LLT (Long Life Tech). (0.25kW to 0.75kW) -
PG models (non-automatic)/PGA models (automatic)- Submersible PumpsPlastic/stainless steel models
- Products for general households
- for industrial equipment
- for pit gray water
●Wide range of applications such as clean water, sewage, and waste water.
● All wetted parts are made of resin and stainless steel for excellent rust resistance and durability.
● New mechanism that can change the discharge direction either "vertically" or "horizontally". (excluding 1.5kW and 2.2kW)
● Back pull-out structure that allows inspection and cleaning while piping is connected.
●Equipped with an automatic burnout prevention device in the motor.
● Cooling and lubricity of the mechanical seal are improved by adopting LLT (Long Life Tech). (0.25kW to 0.75kW) -
TCVS models (non-automatic)- Submersible PumpsCast Iron Models
for civil engineering- for industrial equipment
- for kitchen wastewater
- for pit gray water
- for septic tank
●The newly designed high-performance whirlpool impeller prevents clogging and winding even in sewage containing fibrous contaminants.
● Low-wear type that prevents foreign matter from directly passing through the impeller.
●Built-in automatic return type motor protection device (auto cut).
●The shaft seal uses a double mechanical seal and an oil seal. (1.5 kW or more when combined with an oil seal)
●SiC with excellent wear resistance is used for the sliding part of the mechanical seal.
FAQs
Provides help information on how to use each product and when you have problems.
